Stalker Radar brand of police radar, law enforcement laser and lidar, and sport speed measurement guns from Applied Concepts.

The Stalker LED Speed Sign interfaces with sport radar guns through
the use of connectors and dedicated cables:

Model	Cable (connector)
Stalker ATS II	155-2284-00
Stalker Pro II	155-2284-00
Stalker Sport 2	155-2287-25
Stalker Solo 2	155-2287-25
Stalker Pro	155-2271-00 For radars without and RS232 port require a Handle with Data Connector 200-0163-02 155-2287-25 For radars with RS232 port.*
Stalker Sport	155-2271-00 For radars without and RS232 port require a Handle with Data Connector 200-0163-02 155-2287-25 For radars with RS232 port.*
Jugs Pro-Sports	155-2287-25
Jugs Si Arcade	155-2312-20

* Requires a Battery Handle ((200-0480-00) or Corded Handle (200-0163-00)

Model:	2½-Digit Speed Sign	3½-Digit Speed Sign
Dimensions:	15.5” (39.4cm) wide 9.5” (24.1cm) high 1.375” (3.5cm) deep	21.5” (54.6cm) wide 9.5” (24.1 cm) high 1.375” (3.5cm) deep
Weight:	6.05 lbs. (2.74kg)	8.05 lbs. (3.65kg)
Digit height:	8.0” (20.3cm)	8.0” (20.3cm)
Input Voltage:	8 to 24 volts (.12 A @12 VDC)	8 to 24 volts (.15 A @12 VDC)

Stalker LED Speed Signs are manufactured in the United States and backed by a full 1-year warranty.

The LED Speed Sign is weather resistant, but should be kept out of heavy rain. The external power supply is not waterproof and should be kept dry at all times

 

Stalker LED Speed Sign Setup and Configuration:

LED Speed Sign Setup
The Stalker LED Speed Sign features rotating feet that fold parallel to the sign’s case for easy storage. To position the Speed Sign on a flat surface, rotate the feet 90 degrees so that they are perpendicular to the sign’s face. Alternatively, hang the sign using the integral top-corner hooks.

Connecting a Radar and a Sign
In order for the Speed Sign to properly recognize the particular radar gun model and its data, the unit(s) should be connected in the following manner:

1) connect data cable to radar and sign
2) apply power to sign by connecting the external power supply*
3) power up radar

* EXTERNAL POWER SUPPLY IS NOT WATERPROOF. KEEP DRY AT ALL TIMES.

Speed Sign Controls
The Stalker LED Speed Sign’s controls are located on the lower left side of the unit. A momentary push-button switch initiates LED testing sequences in the following modes:

Push 1 – Table Demonstration Mode: Slowcount, full digit flash, slow count, fast count, loop...
Push 2 – Fast count
Push 3 – All LEDs on
Push 4 – Show software version
Push 5 – Enter normal mode

Configuration
To configure multiple LED Speed Signs using the Stalker Pro II radar, use Speed Sign multiple sign cabling hub, 200-0815-00. Set DIP switches 6, 7, and 8 to their appropriate positions before connecting the radar and signs.

Switch Position	2½-Digit Speed Sign part number - 200-0778-00	3½-Digit Speed Sign part number - 200-0779-00
Switch 1: ON	Set to ON (↑) when K-Sport or Sport Pro output is TTL (data from bottom of the handle). Set to OFF (↓) for all other radars.
Switch 2: ON	100% brightness.
Switch 3: Reserved	Unused
Switch 4: Reserved	Unused
Switch 5: ON, Ignore Decimal Point	The 2½-Digit LED Speed Sign ignores the decimal point and anything following.	The 3½-Digit LED Speed Sign ignores anything following the decimal point. “123.4” is displayed as “123”. “1234.5” is displayed as “1234”.
Switch 6: ON	Displays - Release Speed	For bE format. Switches select which Speed Reading is displayed.
Switch 7: ON	Displays - Plate Speed
Switch 8: ON	Displays - Hit Speed
Default setting: All 8 switches OFF.

 

Brochure Downloads

Click here to download the Stalker LED Speed Sign brochure

Click here to download the Stalker LED Speed Sign Compatibility Chart