Return to home page Return to home page
Stalker Stationary Speed and Traffic Statistics Sensor Stalker Low Speed Sensor Stalker Traffic Statistics App Stalker 6x26 degree sensors

Stalker Pro II Speed Sensor Radar

How to choose Sensors

Powerful, Feature-loaded Sports Speed Measurement Radar

The Pro II Speed Sensor is a complete and highly-accurate Doppler Radar in a small, rugged waterproof housing that can measure the speed of a wide variety of objects including baseballs, vehicles, tennis balls, and hockey pucks. It combines features and performance of the Stalker Pro II handheld sport gun with the Sport Speed Sensor configuration. The unit is available in an RS-232 model and an RS-485 model and includes complete software support. 

  • Same performance as the Major League favorite Pro II Hand held
  • Waterproof design
  • PC application available for configuration and communication
    with the radar.
  • Reports speeds in MPH, km/s, knots, feet/second, or
    meters/second in whole units or tenths resolution.
  • Measures speeds up to 890 MPH.
  • Directional - tracks objects moving in either direction.
  • Reports Live (Rolldown), Peak, and Highest Peak speeds in one direction; Hit speeds in opposite direction.
  • Detects baseballs to 500' and average-sized automobiles to 1 3/4 miles
  • Wide range of High and Low Speed Thresholds to focus on speed range of interest.
  • Tracks everything from car-sized objects (and larger) to BBs.
  • Configuration of Pro II Speed Sensor package Configuration
    Click to enlarge
  • Automatic cosine angle adjustment compensates for both off-horizontal and off-vertical angle readings
  • Waterproof; Ka-Band, 34.6 GHz; 15mW nominal power output; +/- 3% accuracy.
  • Connect multiple radars in point-to-multipoint configuration (RS-485)
  • A, A1, b, bE, and S streaming data protocols.
Stalker Pro II Speed Sensor - RS-232
Stalker Pro II Speed Sensor at Frisco Rough Rider Stadium Stalker Traffic Control Sensor

 

 

 

 

  • SCOREBOARD SOFTWARE
  • SPECIFICATIONS
  • ACCESSORIES
  • DOWNLOADS
Scoreboard Landing page

Scoreboard configuration page

Stalker Radar Scoreboard Application Software

The Scoreboard PC application used to configure, control and monitor the Stalker Pro II Speed Sensor. This is the cornerstone of the PRO II Speed Sensor Developer’s kit.

  • Clean and clear graphics for displaying sensor readings.
  • Easy to navigate for setting sensor configuration.
  • New detailed users manual to guide the user through the program’s operation.
  • Upgrade a sensor’s software from within the Scoreboard application.
  • Automatic sensor and Baud rate detection.

200-0863-00 Pro II Speed Sensor Developers Kit, RS-232

Included in the kit are the following:

  • RS-232 Speed Sensor Programming box
  • Speed Sensor Developers Kit CD
  • RS-232 Straight-through cable
  • Speed Sensor Power and I/O cable, 12'
  • Speed Sensor Power I/O user cable parts

200-0864-00 Pro II Speed Sensor Developers Kit, RS-485

Included in the kit are the following:

  • RS-485 Speed Sensor Programming box
  • Speed Sensor Developers Kit CD
  • RS-485 Straight-through cable
  • Speed Sensor Power and I/O cable, 82'

 

 

 

General Specifications:

Product Type Stationary Doppler Radar Speed Sensor
Processor Digital Signal Processor
Operating Temperatures -30°C to +70°C (-22°F to +158°F), 90% relative humidity
Storage Temperatures -40°C to +85°C (-40°F to +185°F)

Microwave Specifications:

Operating Frequency 34.7 GHz (Ka-band)
Frequency Stability ±100 MHz
Antenna Type Conical Horn
Polarization Circular
3 db Beam Width 12°±1°
Microwave Source Gunn-Effect Diode
Receiver Type Two direct-conversion homodyne receivers using four low-noise
Schottky barrier mixer diodes
Power Output 25 mW nominal
Power Density 1 mW/cm2 maximum at 5 cm from lens

The Federal Communications Commission requires that all transmitting equipment carry a Grant of Type Acceptance.
The Stalker Speed Sensors comply with Part 90 of the FCC rules and are Type Accepted by the FCC under
Type Acceptance number IBQACMI002.
The FCC also requires that an operating license be obtained by the user of the equipment.

Performance Specifications:

Speed Range Max target speed: 800+ MPH
Min target speed: < 1 MPH
Accuracy +/- 3%
In ones resolution, speeds are rounded to nearest integer.
In tenths resolution, speeds are rounded to nearest tenth.
Maximum Clocking Distance 500 Feet for baseballs
1 ¾ Miles for an average auto
Audio Output Raw 3.3 V analog audio output signal is provided for Doppler audio – must be filtered and amplified for best audio quality.
Speed Alarm Output

With speeds below the Alarm Threshold, the Aux pin outupt is 0.0V
With speeds at or above the Alarm Threshold, the Aux pin is 3.3V and can drive 10mA.

Electrical Specifications:

Supply Voltage 9 – 28 VDC
Current (at 12 VDC nominal) Transmitter On: 390 mA
Transmitter Off: 138 mA

Physical Specifications:

Weight 1.15 lb (0.52 kg)
Diameter 2.6 in (6.7 cm)
Length 4.7 in (11.8 cm)
Case Material Aluminum die cast

Stalker Pro II Speed Sensor configuration Configuration
Click to enlarge

Click on the links below to download:

Pro II Speed Sensor brochure

Pro II Speed Sensor and Scoreboard PC Application Users Manual

 Configuration files

Download Configure Pro II Speed Sensor 232 1.0.1.cfg file.

Download Configure Pro II Speed Sensor 232 1.0.2.cfg file.

Download Configure Pro II Speed Sensor 232 1.0.3.cfg file.

Download Configure Pro II Speed Sensor 232 2.0.0.cfg file. (Beginning with Serial Numbers SW001080 and newer)
Note: New software is not backward compatible with older hardware.

Download Configure Pro II Speed Sensor 232 2.0.1.cfg file.


Download Configure Pro II Speed Sensor 485 1.0.1.cfg file.

Download Configure Pro II Speed Sensor 485 1.0.2.cfg file.

Download Configure Pro II Speed Sensor 485 1.0.3.cfg file.

Download Configure Pro II Speed Sensor 485 1.0.4.cfg file.

Download Configure Pro II Speed Sensor 485 2.0.0.cfg file. (Beginning with Serial Numbers SX001020 and newer)
Note: New software is not backward compatible with older hardware.

Download Configure Pro II Speed Sensor 485 2.0.1.cfg file.

 Programming files

Download setupDownloadS3ProII101.exe.

Download setupDownloadS3ProII102.exe.

Download setupDownloadS3ProII103.exe.

Download setupDownloadS3ProII200.exe. (Beginning with Serial Numbers SW001080 and newer)
Note: New software is not backward compatible with older hardware.

Download setupDownloadS3ProII201.exe.


Download setupDownloadS3ProII485101.exe.

Download setupDownloadS3ProII485102.exe.

Download setupDownloadS3ProII485103.exe.

Download setupDownloadS3ProII485104.exe.

Download setupDownloadS3ProII485200.exe. (Beginning with Serial Numbers SX001020 and newer)
Note: New software is not backward compatible with older hardware.

Download setupDownloadS3ProII485201.exe.

 

REACT Application Downloads

ACIRemoteMntClient.zip