Stalker Stationary Speed Sensor
When measuring speed from a fixed position, the Stationary Speed Sensor is the right choice. The Speed Sensor’s waterproof case allows it to be mounted in any outdoor location. Use it anywhere that speed measurement from a fixed location is the primary requirement.
Features of the Stalker Stationary Speed Sensor
Stationary Speed Sensor application
The Stalker Stationary Sensor ...........................
General Specifications
Type |
Stationary Doppler Radar Speed Sensor |
Operating Frequency | 34.7 GHz (Ka-Band) |
Stability | +/-100 MHz |
Communication Interface | RS-232 or RS-485 available as separate models |
Power Requirements | Voltage: 9-16 VDC for SN ST6560 and below Current: (at 12 VDC nominal) |
Environmental | Operating: -22° F (-30° C) to +158° F (+70° C) , 90% relative humidity, Non-operating: -40° F (-40° C) to +185° F (+85° C) |
Mechanical | Weight: 1.15 lb. (0.52 kg) Diameter: 2.6 in. (6.7 cm) Length: 4.7 in. (11.8 cm) Case Material: Aluminum Die Cast |
Accuracy | +/- 3% - Speeds are rounded down to the nearest unit or tenths of a unit depending on the unit resolution setting |
Audio Output | A 3.3 Vpp pulse-width modulated (PWM) audio output signal is provided - must be filtered and amplified for best audio quality. |
Auto Self-Test | Performed every 10 minutes while transmitting |
Speed Range | Stationary low speed threshold configurable: |
Microwave Specifications:
Antenna | Conical horn |
Polarization | Circular |
3DB Beamwidth | 12° +/- 1° |
RF Source | Gunn-Effect diode |
Receiver Type | Two Direct-Conversion Homodyne receivers using four low-noise Schottky battier mixer diodes |
Power Output | 10 mW minimum |
Power Density | 1 mW/cm2 maximum at 5 cm from lens |
Control and Configuration Settings
Basic Configuration | Transmitter Control Zone Unit of Measure Unit Resolution Faster Target Tracking AUX Pin Configuration |
Serial Port Configuration | Baud Rate Output Format Leading Zero Character Format D Direction Character Enable (RS-232 only) Zeros After Target (RS-232 only) Message Period Format D Update on Change Only (RS-232 only) Format D Zero Report (RS-232 only) Polled Modes D0-D4 (RS-232 only) |
Target Recognition | Opposite Lane/Stationary Sensitivity Fine Sensitivity Adjust Sensitivity Hysteresis Low Sensitivity Target Strength Sensitivity Target Acquisition Quality Target Loss Quality |
Target Filtering | Stationary Low Cutoff Spurious Speed Filter Max AGC Gain Min AGC Gain Current AGC Gain |
Speed Presentation | Cosine 1 Angle Cosine 2 Angle Holdover Delay |
Locking Targets | Lock Option Faster Locking Enable Strongest Lock Fast Lock |
Speed Alarm | Alarm Speed Threshold |
Audio | Doppler Audio Volume Aud 0 Enable Variable Doppler Loudness Squelch Beep Volume |
TX Power Save | TX On Time TX Off Time Keep TX On with Target Max TX On Time |
Testing | Fork Enable Auto Test Period Auto Test Mode Enhanced Test |
System | Get Product ID Get Product Type Get Software Version Speed Sensor Address (RS-485 only) |
View / Download Stationary Speed Sensor manual.
(Left click to view / Right click to download.)View / Download Speed Sensor brochure.
(Left click to view / Right click to download.)View / Download Stationary Speed Sensor technical specifications.
(Left click to view / Right click to download.)
View / Download Speed Sensor Certificate of Accuracy.
(Left click to view / Right click to download.)Configuration files:
Note: New software is not backward compatible with older hardware.Download Stationary 232 2.0.0 cfg file.
Download Stationary 232 2.0.1 cfg file.
Download Stationary 232 2.0.2 cfg file.
Download Stationary 232 3.0.0 cfg file. (Beginning with Serial Numbers ST009700 and newer)
Note: New software is not backward compatible with older hardware.Download Stationary 232 3.1.0 cfg file.
Download Stationary 485 2.0.0 cfg file.
Download Stationary 485 2.0.1 cfg file.
Download Stationary 485 2.0.2 cfg file.
Download Stationary 485 3.0.0 cfg file. (Beginning with Serial Numbers SU2000 and newer)
Note: New software is not backward compatible with older hardware.Programming files:
Download setupDownloadSTA200exe.
Download setupDownloadSTA201exe.
Download setupDownloadSTA202exe.
Download setupDownloadSTA300exe. (Beginning with Serial Numbers ST009700 and newer)
Note: New software is not backward compatible with older hardware.Download setupDownloadSTA310exe.
Download setupDownloadSTA485200exe.
Download setupDownloadSTA485201exe.
Download setupDownloadSTA485202exe.
Download setupDownloadSTA485300exe. (Beginning with Serial Numbers SU2000 and newer)
Note: New software is not backward compatible with older hardware.
REACT Application Downloads